Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
en:services:it_consulting:apple_consulting_center:mac_network:mac_vpn [2020/06/26 10:20] – translated german version fketten | en:services:it_consulting:apple_consulting_center:mac_network:mac_vpn [2023/09/19 08:53] – [Connect by using the integrated VPN Client] dimpell | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Setup of a VPN Connection ====== | ||
+ | ===== General Information ===== | ||
+ | You can find general information about VPN connections [[en: | ||
+ | |||
+ | <WRAP center round important 60%> | ||
+ | The GWDG strongly recommends using the Cisco AnyConnect VPN. | ||
+ | </ | ||
+ | |||
+ | |||
+ | For macOS 10.6 and later, it is possible to use the VPN with on-board software and without installing an additional client (see below). | ||
+ | **Attention**: | ||
+ | |||
+ | <WRAP center round important 100%> | ||
+ | Due to the current load in VPN, two more servers were set up in addition to vpn.gwdg.de: | ||
+ | |||
+ | Please make sure to switch to **vpn.gwdg.de** once in a while since updates will not be delivered while using **vpn-b.gwdg.de** or **vpn-c.gwdg.de**. | ||
+ | </ | ||
+ | |||
+ | ===== Connection via Cisco AnyConnect ===== | ||
+ | |||
+ | ++++ Step-by-step image instruction: | ||
+ | |||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | ++++ | ||
+ | |||
+ | Should you encounter any issues during this process, please contact [[https:// | ||
+ | |||
+ | 1. Connect to [[https:// | ||
+ | |||
+ | **Attention: | ||
+ | |||
+ | 2. Click on // | ||
+ | |||
+ | 3. Click on //Start AnyConnect// | ||
+ | |||
+ | 4. Install AnyConnect from the file you have just downloaded. Please make sure that you are in possession of sufficient administration rights on your system or consult your system administrator. | ||
+ | |||
+ | 5. Open the newly installed //Cisco AnyConnect Secure Mobility Client// to start the VPN. | ||
+ | |||
+ | 6. Insert any gateway address (**vpn-b.gwdg.de** or **vpn-c.gwdg.de** or **vpn.gwdg.de**) and click on // | ||
+ | |||
+ | 7. Enter your credentials. These are usually your email address and the corresponding password. | ||
+ | |||
+ | 8. Accept the terms and conditions for using the VPN. | ||
+ | |||
+ | You are now connected to the VPN. | ||
+ | |||
+ | If you want to start the VPN again, just start the client directly. It is not necessary to install the program again. | ||
+ | |||
+ | |||
+ | <WRAP center round important 100%> | ||
+ | Due to the current load in VPN, two more servers were set up in addition to vpn.gwdg.de: | ||
+ | |||
+ | The AnyConnect Client can also be downloaded from https:// | ||
+ | * Username: vpn | ||
+ | * Password: fernzugriff | ||
+ | </ | ||
+ | |||
+ | ===== Connect by using the integrated VPN Client ===== | ||
+ | |||
+ | <WRAP center round important 60%> | ||
+ | The GWDG strongly recommends using the Cisco AnyConnect VPN. Therefore, the use of the VPN solution integrated in macOS is not advised. [[en: | ||
+ | </ | ||
+ | |||
+ | |||
+ | **Attention: | ||
+ | |||
+ | With Mac OS X Snow Leopard (10.6) or later, you can use the built-in VPN client directly. | ||
+ | |||
+ | 1. Open System Preferences and click on " | ||
+ | |||
+ | 2. Click the plus icon to add a new connection. | ||
+ | |||
+ | 3. Click " | ||
+ | |||
+ | 4. For " | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | 5. Click " | ||
+ | |||
+ | For the " | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | |||
+ | 6. Now click on the button " | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | 7. Now you can establish a VPN connection by clicking " | ||
+ | |||
+ | 8. If you have enabled the VPN status in the menu bar, you can always start and exit the VPN connection with GoeMobile by clicking on the corresponding icon. | ||
+ | |||
+ | 9. For logging in to VPN, you must authenticate yourself. Students type their username as " | ||
+ | |||
+ | Be sure not to type " |