Table of Contents
Common Errorcodes
Many tips are given in the document Server Messages and Error Codes, especially in Chapter 4. Descriptions of I/O codes in server messages or in the Problem Determination Guide ISP7.1.0 or Problem Determination Guide ISP8.1.0
This page will move to the Operational Documentation of SP at GWDG
ANR1664W
trying to remove a replication server fails:
Protect: SM286>del server SM287 ANR1664W DELETE SERVER: Server SM287 is currently in use. ANS8001I Return code 12.
ToDo:
- remove ReplicationNode relationships:
REMove REPLnode <NODENAME> SERVER=<Name of Replicationserver>
- if this fail due to ANR3443W / ANR1632E look below
- try again
- if it fails, because it was the last Replication Server you need to assign a blank one by issuing the command without a servername given:
SET REPLServer <nothing!>
- try again
ANR3443W / ANR1632E
Trying to remove a replication relationship from a node fails like this
ANR3443W When the REMOVE REPLNODE command was run, one or more nodes (KOPAL-TEST) were skipped because they are not configured to replicate data to the specified server SM287. ANR3445I If a node has no replication associations with any servers, you must specify an empty string (server="") for the SERVER parameter for the REMOVE REPLNODE command to reset a node's replication state. If the node has a replication association with one or more servers, you must specify a valid target replication server name. ANR1632E REMOVE REPLNODE: Command failed. Replication state information for the specified nodes could not be removed.
Workround:
- remove replicationnode with no server, using just two quote marks:
REMove REPLNode <nodename> REPLServer=''
ANR8302E
KEY = 05
“KEY = 05” means Problems accessing Drive
in relation with
| ASC/ASCQ | Meaning | Source |
|---|---|---|
| ASC=26 , ASCQ=00 + ANR8533W | Due to the 'CHECKTAPEPOS' setting ISP is unable to set the drive to 'APPENDONLY' | IBM-Documentation |
KEY = 06
“KEY = 06” means “Unit Attention”
in relation with
| ASC/ASCQ | Meaning | Source |
|---|---|---|
| ASC=2A, ASCQ=03 | SCSI reservation error because several TSM instances use the same persisten name | https://www-01.ibm.com/support/docview.wss?uid=swg1IT03879 |
| ASC=29 , ASCQ=00 | “Power-on, reset, bus reset” | https://www-01.ibm.com/support/docview.wss?uid=swg1IT20573 |
KEY = FF
ANR8460E
ANR8460E AUDIT LIBRARY process for library <Library Name> failed.
| in combination with | possible reason | solution |
|---|---|---|
ANR9024E There are no drives available. | at least one drive is not available | check drives and make all available |
| check if drives are rotten and if so, remove their definition and paths completely |
ANR8840E
error number 2
| PVRRC | Meaning | Source | Solution |
|---|---|---|---|
| 2843 | unable to access gripper device | – | restart Lintape daemon or Wintape service |
error number 11
| PVRRC | Meaning | Source | Solution |
|---|---|---|---|
| 2845 | Unable to open device <DEVICE> | audit library failed after drives / paths got unavailable | scsi information mismatch: |
| * reboot server | |||
| * reboot library | |||
| * force rescan scsi bus on device layer | |||
* check if the lintape driver is running  |
ANR8779E
ANR 8779E Unable to open drive <NAME>, error number= 2
in combination with
ANR1401W
ANR1401W Mount request denied for volume <NAME> - mount failed.
Possible Reasons:
- SCSI connection lost on Library Client:
- Solution: rescan the SCSI bus:
⇒ run as root:rescan-scsi-bus.sh
- Persitent Naming fails due to an temporary SCSI-Error
- Solution: let the udev daemon reload the rules:
⇒ run as root:udevadm trigger